The LT Brushless Power System is a customized full featured 1/8th Scale 150A 6S Brushless / Sensorless ESC + 1510Kv XL Motor.

This system is intended for use with 6S Lipo.  It is suitable for most 1/8th and 1/10th brushless vehicles and conversions.  A perfect candidate for E-Revo / E-Maxx / Summit.

Setup tip: use the speed calculator by Brian Gosselin to figure out what pinion/spur you need.  An average speed of 35-40mph is recommended.

The LT-6S-150A ESC may look similar to your typical aircraft ESCs but it is a completely different beast. The LT-6S-150A ESC features full forward/brake/reverse at 150A continuous, flexible programmable features, and not to forget the included compact portable programming card which allow you to easily change any ESC functions with a few clicks of buttons.  This ESC has been through extended testing and proven to handle most 1/8th and 1/10th brushless vehicles and brushless conversions.  This system is bundled with a nice finned can 1510Kv brushless motor with strong 5mm shaft.  Note: other Kv can be custom ordered upon request.

Note about motor shaft: For some reason, the motor shaft doesn't come with a flat spot for the pinion, but a dremel or a hand filer should easily get the job done.

ESC Programming Card:

Here are some test data showing average and peak current from different setup (credit to Luciano)

Click to enlarge.

Features:

• Full protection feature including low voltage, over-heat, signal loss, startup protection and self-check.
• Compatible with sensorless brushless motor.
• Excellent startup performance, great throttle linearity and quick throttle response.
• Support highest motor speed 240,000RPM (2 poles), 80,000RPM (6 poles) and 40,000RPM (12 poles).
• Easy configure with LCD program card (included, $20 value).
• System can automatically detect throttle neutral point and neutral range is adjustable.
• Four running modes can match different requirement.
• 4 steps of maximum reverse force adjustment, 7 steps of maximum start force adjustment, 5 steps of maximum brake force adjustment, 6 steps of drag brake force adjustment and 6 steps of initial brake force adjustment.
• Powerful finned can brushless motor - 1510Kv - 5mm shaft.
• Finned can brushless motor can reduce heat during run. 
• Full English instruction is included.

Note: For LT-6S-150A and LT-10S-120A, an UBEC or individual battery pack should be required to power the receiver and servos, and the red line (+5V) in 3 pin must be pulled out!

WARNING: The internal BEC of the ESC is may be used to power programming card only.  DO NOT use to power your servos.

10S 120A ESC or complete system is available upon request.

ESC Specs:

P/N	Continuous current	Battery Cell		Dimension (mm) L×W×H	Weight（g）	BEC （Linear For Program Card）	Program By card
		Li-XX	Ni-XX
LT-6S-150A	150A	2-6	5-18	96x55x21	180	0.2A/5V	Yes
LT-10S-120A	120A	2-10	5-30	96x55x21	180	0.2A/5V	Yes

Note: For LT-6S-150A and LT-10S-120A, an UBEC or individual battery pack should be required to power the receiver and servos, and the red line (+5V) in 3 pin must be pulled out!

WARNING: The internal BEC of the ESC is may be used to power programming card only.  DO NOT use to power your servos.

Motor Specs:

• Kv:  1510 rpm/Volt
• Dimension: 43.3x74.8mm (with fins)
• Shaft: 5mm
• MAX Input Voltage: 22.2v (6s Lipo)
• MAX Current: 60A
• Resistence:  0.0158
• I0(A): 2.3
• Connector: 4mm Gold Bullet

Install into vehicle, requires soldering and modification to stock chassis in order to fit.